This is a working overview of collapse temperature, written for readers who want more than a one-paragraph summary but less than a textbook.
This page was last updated on 2025-11-11 and is reviewed periodically as new material appears.
A freeze-dryer consists of a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. Vials, ampoules, or bulk trays hold the product during the cycle. The condenser traps water vapor as ice at a temperature lower than the product. Cycle development balances shelf temperature, chamber pressure, and time. Scale-up can be difficult because heat and mass transfer change with equipment size, so process analytical tools and conservative validation are often used.
Lyophilization is a dehydration technique in which a product is frozen and the solvent is removed under reduced pressure. The low pressure allows ice to sublimate directly into vapor without passing through a bulk liquid phase. This differs from conventional drying, where heat drives evaporation and can damage heat-sensitive structures. The process is used for biological materials, pharmaceutical formulations, and some foods. Its main advantage is preservation of porous structure and rapid reconstitution.
Quality control also examines cake structure, color, and reconstitution behavior. A collapsed or shrunken cake can indicate a thermal excursion during drying. Analytical methods such as X-ray diffraction, differential scanning calorimetry, and near-infrared spectroscopy can detect crystallinity or moisture distribution. Regulatory expectations focus on validated assays and lot-to-lot consistency. Questions remain about how well accelerated stability tests predict long-term behavior for every formulation. Visual inspection remains common but is subjective without trained reviewers and reference images.
After lyophilization, a product's quality depends on residual moisture, cake appearance, and reconstitution time. Residual moisture is often measured by Karl Fischer titration or thermogravimetric analysis. A low moisture content can slow chemical degradation, but overly dry cakes may be brittle or slow to dissolve. Stability studies track these attributes over months under defined temperature and humidity conditions. Batch records link these measurements to specific process runs and help identify trends before a product fails specification.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | freeze-drying, lyophilisation, cryodesiccation | Lyophilization is common in pharmaceutical literature. |
| Typical chamber pressure during primary drying | 0.05–0.5 mbar (5–50 Pa) | Must remain below the triple point of water. |
| Typical shelf temperature during freezing | −40 to −20 °C | Lower temperatures may be used for eutectic systems. |
| Typical residual moisture after secondary drying | 0.5–3% w/w | Product-dependent; low moisture improves stability but can cause over-drying. |
| Typical analytical method for residual moisture | Karl Fischer titration or loss on drying | Thermogravimetric methods are also used. |
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
The physical chemistry of freezing influences whether a formulation forms an amorphous glass or a crystalline solid. Amorphous systems can collapse if product temperature rises above the glass transition temperature of the freeze concentrate. Crystalline systems may show eutectic melting, where ice and solute melt together at a fixed temperature. Formulators add bulking agents, lyoprotectants, and buffers to preserve structure and biological activity. The optimum cycle keeps product temperature below critical thresholds during primary drying while allowing efficient sublimation.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
Lyophilized products are typically hygroscopic and require protection from moisture during storage. Manufacturers seal them in glass vials, often under vacuum or an inert gas such as nitrogen. The container closure system, including the stopper and crimp seal, must prevent water vapor ingress. Storage temperature varies from controlled room temperature to refrigerated or frozen conditions, depending on the formulation. Humidity-controlled environments are essential because even brief exposure to ambient air can degrade the product.
Stability of a lyophilized product depends on its glass transition temperature, the temperature at which the amorphous cake transitions from a glassy to a rubbery state. Storage below this temperature minimizes molecular mobility and slows chemical degradation. If the storage temperature exceeds the glass transition temperature, the cake may collapse, shrink, or become sticky. Accelerated stability studies at elevated temperatures and humidity help predict shelf life, but they do not always reflect real-time behavior. Residual moisture content also plays a critical role in long-term stability.
Lyophilization, also called freeze-drying, is a dehydration process in which a solvent, usually water, is frozen and then removed by sublimation under reduced pressure. The method preserves heat-sensitive materials that would degrade in conventional drying. Large-scale use grew during the mid-twentieth century for blood plasma and antibiotics, and it later expanded to vaccines, enzymes, foods, and advanced materials. The process produces a dry, porous solid that usually reconstitutes rapidly. It is distinct from simple evaporation because the solvent bypasses the liquid phase during primary removal.
The process generally proceeds in three stages: freezing, primary drying, and secondary drying. During freezing, controlled cooling converts water into ice and may also crystallize or vitrify solutes. In primary drying, the pressure is lowered below the triple point, and heat is supplied so ice sublimes directly to vapor. Secondary drying removes water that remains bound to the solid matrix, yielding a low final water content. Product temperature must stay below the collapse or glass transition temperature to maintain structure. Cycle design therefore balances shelf temperature, chamber pressure, and time.
Freeze-drying is used for materials whose activity or structure depends on low temperature and low water content. Examples include certain biologics, diagnostic reagents, starter cultures, coffee, and porous inorganic precursors. The dried product forms a cake whose porosity aids rapid wetting and dissolution. Main drawbacks are high energy use, long cycle times, and sensitivity to formulation and equipment variation. Questions remain about how freezing rates and ice morphology affect batch uniformity, especially when moving from laboratory to production scale.
Quality control for lyophilized materials examines appearance, reconstitution time, residual moisture, and mechanical integrity. An acceptable cake is usually uniform and porous, though appearance alone does not prove stability. Karl Fischer titration is a common method for water content, while differential scanning calorimetry can reveal glass transition events. Stability studies track potency, aggregation, and moisture over time under defined temperature and humidity conditions. Specifications are product-specific and may include sterility and endotoxin tests for sterile preparations.
Misconceptions about lyophilization include the idea that dried products are indefinitely stable or that vacuum sealing eliminates all degradation. Chemical reactions can continue in the solid state, and some proteins lose activity even at low moisture. Another misconception is that any freeze-dryer cycle can be scaled by time alone; heat and mass transfer differ with equipment and load. Open questions remain about predicting long-term stability from short accelerated studies, particularly for amorphous formulations. Real-time stability data remain the standard for shelf-life assignment.
C11orf91 has a predicted Protein kinase C (PKC) phosphorylation site, Casein kinase 2 (CK2) phosphorylation site, amidation site, and two predicted serine phosphorylation sites, see Conceptual Translation for post-translational modification site locations. There are no paralogs of the human C11orf91 protein. The human C11orf91 protein has several orthologs found across eight categories of jawed vertebrates including: aves, testudines, alligators, reptiles, mammals, amphibians, lungfishes, and cartilaginous fishes.
Alfred Ellis Wilhelmi (1910–1994) was an American endocrinologist recognized for contributing to the understanding of anterior pituitary hormones. Born in Lakewood, Ohio, Wilhelmi attended Cleveland public schools. Wilhelmi earned a B.S. degree in premedical sciences from Western Reserve University in 1933. He then attended Oxford University as a Rhodes Scholar, where he obtained a B.A. in 1933 and Ph.D. in animal physiology in 1937. He then joined Yale University's Biochemistry Department, rising to the position of Professor in 1950. Wilhelmi chaired the Department of Biochemistry at Emory University School of Medicine from 1950 to 1977. In 1960, he was named Charles Howard Candler Professor of Biochemistry. In 1979, he received Emory's Thomas Jefferson award for service to the university and community. Wilhelmi also was President of the Endocrine Society from 1968 to 1969. During his career, he published over 80 articles in scientific journals.
Antidotes can be employed to either mop up hazardous metabolites or change them into less toxic forms once they have developed. Hepatic glutathione stores are replenished by N-acetyl cysteine, and this process is what leads to the conjugation of the poisonous metabolite N-acetyl P-benzoquinone imine (NAPQI). Receptor antagonist Receptor Dose–response relationship Pharmacodynamics Antidotes
Biomaterials are used in: Joint replacements Bone plates Intraocular lenses (IOLs) for eye surgery Bone cement Artificial ligaments and tendons Dental implants for tooth fixation Blood vessel prostheses Heart valves Skin repair devices (artificial tissue) Cochlear replacements Contact lenses Breast implants Drug delivery mechanisms Sustainable materials Vascular grafts Stents Nerve conduits Surgical sutures, clips, and staples for wound closure Pins and screws for fracture stabilisation Surgical mesh Biomaterials must be compatible with the body, and there are often issues of biocompatibility, which must be resolved before a product can be placed on the market and used in a clinical setting. Because of this, biomaterials are usually subjected to the same requirements as those undergone by new drug therapies. All manufacturing companies are also required to ensure traceability of all of their products, so that if a defective product is discovered, others in the same batch may be traced.
Normal phase elution is achieved by pumping the non-aqueous or phase of a biphasic solvent system through the column as the mobile phase, with a more polar stationary phase being retained in the column. The cause of original nomenclature of is relevant. As original stationary phases of paper chromatography were superseded by more efficient materials such as diatomaceous earths (natural micro-porous silica) and followed by modern silica gel, the thin-layer chromatography stationary phase was polar (hydroxy groups attached to silica) and maximum retention was achieved with non-polar solvents such as n-hexane. Progressively more polar eluents were then used to move polar compounds up the plate. Various alkane bonded phases were tried with C18 becoming the most popular. Alkane chains were chemically bonded to the silica, and a reversal of the elution trend occurred. Thus a polar stationary became "normal" phase chromatography, and the non-polar stationary phase chromatography became "reversed" phase chromatography.
Sources: en.wikipedia.org
Brunton Medal 1979, Sir Francis Avery Jones research medal of the British Society of Gastroenterology, the highest research award that the national gastroenterology body confers on its researchers. Fellowships: Royal Colleges of Physicians of Glasgow (1975) London (1977) Edinburgh (1981) Royal College of Pathologists (1984) Fellow of the Royal Society of Edinburgh (1990) The Anne Ferguson building at the Western General Hospital, Edinburgh, is named after her. In 1966, she married John Ferguson, a sociology lecturer at the University of Strathclyde, and together they adopted two children, a girl and a boy. John Ferguson died of cancer in 1989. She married Professor Gerald Collee, emeritus Professor of Medical Microbiology at the University of Edinburgh in 1995. In her youth, Ferguson represented the University of Glasgow in athletics as a middle-distance runner. She was also on the Scottish women's basketball team. She enjoyed hill walking and mountaineering, and once visited the Himalayas with her first husband. Ferguson died of pancreatic cancer in Edinburgh on 21 December 1998.
Investigators have hypothesized that the PHLPP isoforms may play roles in cancer, for several reasons. First, the genetic loci coding for PHLPP1 and 2 are commonly lost in cancer. The region including PHLPP1, 18q21.33, commonly undergoes loss of heterozygosity (LOH) in colon cancers, while 16q22.3, which includes the PHLPP2 gene, undergoes LOH in breast and ovarian cancers, Wilms tumors, prostate cancer and hepatocellular carcinoma. Second, experimental overexpression of PHLPP in cancer cell lines tends to decrease apoptosis and increase proliferation, and stable colon and glioblastoma cell lines overexpressing PHLPP1 show decreased tumor formation in xenograft models. Recent studies have also shown that Bcr-Abl, the fusion protein responsible for chronic myelogenous leukemia (CML), downregulates PHLPP1 and PHLPP2 levels, and that decreasing PHLPP levels interferes with the efficacy of Bcr-Abl inhibitors, including Gleevec, in CML cell lines. Finally, both Akt and PKC are known to be tumor promoters, suggesting that their negative regulator PHLPP may act as a tumor suppressor.
Parker was born in March 1938, and was the only daughter of Frederick and Hilda Witcomb (née Linscott). She was married to Joseph Parker, a Post Office engineer, and lived in the Kings Norton area of Birmingham. After several years as a police photographer, she joined the University of Birmingham Medical School, where she was employed as a medical photographer in the Anatomy Department. She often worked in a darkroom above the laboratory where research on smallpox viruses was being conducted.
While many of the claims are based on scientifically based physiological or biochemical processes, their use in bodybuilding parlance is often heavily colored by bodybuilding lore and industry marketing and, as such, may deviate considerably from traditional scientific usages of the terms. In addition, ingredients listed have been found at times to be different from the contents. In 2015, Consumer Reports reported unsafe levels of arsenic, cadmium, lead, and mercury in several of the protein powders that were tested. In the United States, the manufacturers of dietary supplements do not need to provide the Food and Drug Administration with evidence of product safety prior to marketing. As a result, the incidence of products adulterated with illegal ingredients has continued to rise. In 2013, one-third of the supplements linked to liver damage in one study were adulterated with unlisted steroids. More recently, the prevalence of designer steroids with unknown safety and pharmacological effects has increased. In 2015, a CBC investigative report found that protein spiking (i.e., the addition of amino-acid filler to manipulate analysis) was not uncommon; however, many of the companies involved challenged these claims.
Sources: en.wikipedia.org
Yes, the terms are generally interchangeable. Lyophilization is more common in pharmaceutical and laboratory contexts, while freeze-drying appears widely in food science and general writing. Both describe removal of solvent by sublimation under vacuum after freezing.
Reduced pressure keeps the process below the triple point of water, so ice can sublimate directly to vapor. It also lowers the temperature needed for drying, which helps preserve heat-sensitive materials. Without vacuum, melting or boiling could occur instead of controlled sublimation.
The rate depends on heat transfer to the product and mass transfer of vapor through the dried layer. A cold condenser, adequate vacuum, and suitable shelf temperature all influence speed. Formulation properties such as solid content and collapse temperature also set practical limits.
Karl Fischer titration is a common reference method that quantifies water by a chemical reaction. Thermogravimetric analysis can also estimate moisture by weight loss on heating. Method choice depends on sample size and whether other volatile substances are present.